下陆区是黄石市四个城区之一，地处黄石市中心腹地，东接黄石港、西塞山，西连铁山，南邻大冶，北靠鄂州。现辖新下陆、老下陆、东
| 序号 No. | 部位 Part | 材料 Material |
| 1 | 主体 Body | 氟橡胶(FKM) |
| 2 | 内、外衬 Inner & Outer Rubber | 氟橡胶(FKM) |
| 3 | 主体骨架 Body Carcass | 尼龙帘布 Nylon cord fabric |
| 4 | 增压环 Reinforcing Ring | 多股镀铜钢丝 Multi-strand coppering steel wire |
| 5 | 法兰 Flange | 铸造、锻造碳钢 Cast and forged carbon steel(Q235)、不锈钢 Stainless steel(201、304、316、321)、塑料 Plastic(CPVC、PVDF、PPH、UPVC、RPP) |
| 项目Item |型号Medol | KXT-1 | KXT-2 | KXT-3 | A、如酸碱物质 B、工作温度有特殊要求 C、也可来函来图定制 D、订货时需说明 A. If media is oil, acid or alkali. B. If special requirements for working temperature C. If OEM orders with drawings or samples D. Please Inform us about above when ordering |
| 工作压力MpaWoring pressure | 1.0(10) | 1.6(16) | 2.5(25) | |
| 爆破压力Mpa Burst Pressure | 2.0(20) | 3.0(30) | 4.5(45) | |
| 真空度 Kpa Vacuum | 53.3(400) | 86.7(650) | 100(750) | |
| 适用温度℃Applicable Temperature | -20℃~+115℃（特殊可达-30℃~+250℃）-20℃~+115℃(-30℃~+250℃ under special conditions) | |||
| 适用介质Applicable Medium | 酸、碱等,acid, alkali, etc. | |||
| 注：主要零件材料同KXT型 Note: the materials of main parts are the same with those of KXT type | ||||
| 公称通径DN Nominal Diameter （mm） |
长度 LengthLmm |
轴向位移 Axial displacement mm |
横向位移 Haorizontal isplacement mm |
偏转角度 Angular deflection(a1+a2)° |
||
| mm |
英寸inch |
伸长Extension | 压缩Compression | |||
| 32 | 1.25 | 95 | 6 | 9 | 9 | 15 |
| 40 | 1.5 | 95 | 6 | 10 | 9 | 15 |
| 50 | 2 | 105 | 7 | 10 | 10 | 15 |
| 65 | 2.5 | 115 | 7 | 13 | 11 | 15 |
| 80 | 3 | 135 | 8 | 15 | 12 | 15 |
| 100 | 4 | 150 | 10 | 19 | 13 | 15 |
| 125 | 5 | 165 | 12 | 19 | 13 | 15 |
| 150 | 6 | 180 | 12 | 20 | 14 | 15 |
| 200 | 8 | 210 | 16 | 25 | 22 | 15 |
| 250 | 10 | 230 | 16 | 25 | 22 | 15 |
| 300 | 12 | 245 | 16 | 25 | 22 | 15 |
| 350 | 14 | 255 | 16 | 25 | 22 | 15 |
| 400 | 16 | 255 | 16 | 25 | 22 | 15 |
| 450 | 18 | 255 | 16 | 25 | 22 | 15 |
| 500 | 20 | 255 | 16 | 25 | 22 | 15 |
| 600 | 24 | 260 | 16 | 25 | 22 | 15 |
| 700 | 28 | 260 | 16 | 25 | 22 | 15 |
| 800 | 32 | 260 | 16 | 25 | 22 | 15 |
| 900 | 36 | 260 | 16 | 25 | 22 | 15 |
| 1000 | 40 | 260 | 18 | 26 | 24 | 15 |
| 1200 | 48 | 260 | 18 | 26 | 24 | 15 |
| 1400 | 56 | 350 | 20 | 28 | 26 | 15 |
| 1600 | 64 | 350 | 25 | 35 | 30 | 10 |
| 1800 | 72 | 350 | 25 | 35 | 30 | 10 |
| 2000 | 80 | 350 | 25 | 35 | 30 | 10 |
| 2200 | 88 | 400 | 25 | 35 | 30 | 10 |
| 2400 | 96 | 400 | 25 | 35 | 30 | 10 |
| 2600 | 104 | 400 | 25 | 35 | 30 | 10 |
| 2800 | 112 | 400 | 25 | 35 | 30 | 10 |
| 3000 | 120 | 400 | 25 | 35 | 30 | 10 |
| 注：1、特殊要求可按用户图纸制作，法兰标准采用9115.1-2000，可选配（GB、JB、HG、CB、ANSI、DIN、BSEN、NF、EN、JIS、 等）法兰标准生产。2、悬空给水使用DN200以上产品，管道必须有固定支撑或固定托架，否则产品应安装防拉脱装置。 3、用户使用橡胶接头，对应法兰应是阀门法兰或符合9115.1-2000法兰。 Notes:1. For OEM orders with special requirement, rubber joints can be made according to customers' drawings. Generally, flange standard is 9115.1-2000, other GB, JB, HG, CB, ANSI, DIN, BSEN, NF, EN, JIS, flanges are also available upon request. 2.When rubber joints size above DN200 are used for overhead water supply system, the pipes must be equipped with fixed supports or fixed brackets, otherwise control units shall be installed on rubber joints. 3.Matching flanges of rubber joints shall be valve flanges or 9115.1(RF) flanges. |
||||||
鑫利管道设备有限公司版权所有 ICP备案：豫ICP备12016377号-2
